Coberturas de Ventosas
Tampas de ventosa MTC
EUROTECH MTC suction cup covers fit over suitable vacuum suction cups and suction plates to provide a non-woven contact layer for glass and other surface-sensitive workpieces. They reduce direct contact between the cup material and the workpiece and may help reduce visible contact marks. Select a candidate cover by cup dimensions and profile, then review the complete configuration for the intended application.
MTC Cover Options at a Glance
- Contact layer: Non-woven cover fitted over a suitable suction cup or suction plate.
- Published round-cup size references: Options from 20 to 550 mm. Check the individual ranges in the size table; this is not a continuous fit range or a lifting-capacity rating.
- Retention: Integrated elastic band. Check fit and retention on the actual cup profile.
- Other dimensions or shapes: Send the cup dimensions and photographs for review.
View MTC models and cup-size references or use the MTC suction cup cover selector to identify a candidate size.
Need help with an existing installation? See what to include in your enquiry.
Coberturas de Ventosas MTC
MTC covers form a non-woven contact layer between a suitable suction cup and the workpiece, helping reduce direct elastomer contact and visible contact marks.
SSUZ Covers for Suction Cup Storage
SSUZ covers protect suction cups when they are not in use. For a workpiece-contact cover used during handling, review the MTC options on this page.
As marcas deixadas pelas ventosas no vidro podem resultar de contaminação, atrito, propriedades do material, pressão de contacto e outras condições de funcionamento. Leia «Por que razão as ventosas a vácuo deixam marcas no vidro?»
Consulte o guia de tamanhos das capas para ventosas da MTC
As capas para ventosas da MTC estão disponíveis numa vasta gama de tamanhos, tanto para ventosas redondas como ovais. A escolha da capa correta depende principalmente das dimensões e da forma da ventosa.
Utilize o nosso guia de tamanhos para identificar uma capa MTC adequada à sua aplicação. Se o seu tamanho não constar da lista, envie-nos o diâmetro da ventosa, as dimensões ou uma fotografia para que possamos ajudá-lo.
- The cover fits over a suitable suction cup or suction plate and is secured with an integrated elastic band. Confirm retention throughout the handling cycle.
- The round-cup selection references listed below range from 20 mm to 550 mm. These dimensions are fit references, not lifting-capacity ratings.
- Confirm material suitability for the workpiece, temperature and any cleaning agents used in your process.
| MTC model | Cup-size reference (mm) |
|---|---|
| MTC 39 | 20 |
| MTC 31 | 40 |
| MTC 8 | 55 – 60 |
| MTC 9 | 70 – 80 |
| MTC 63 | 85 – 95 |
| MTC 1 | 100 – 115 |
| MTC 2 | 120 – 130 |
| MTC 14 | 140 – 150 |
| MTC 3 | 160 – 190 |
| MTC 4 | 200 – 220 |
| MTC 5 | 230 – 250 |
| MTC 30 | 250 – 280 |
| MTC 6 | 280 – 320 |
| MTC 7 | 330 – 350 |
| MTC 10 | 360 – 400 |
| MTC 61 | 500 – 520 |
| MTC 57 | 500 – 550 |
Request an MTC Cover by Model
Use the catalogue model code when requesting a replacement cover. The euroTECH Handling catalogue lists these round-cup diameter references:
- MTC.002 (MTC 2): Ø120 and Ø130 mm.
- MTC.004 (MTC 4): Ø200, Ø210 and Ø220 mm. See the MTC.004 installation on a Ø200 mm float-glass stacking cup.
For oval or drawing-based covers, use the MTC cover selector to check the published sizes and enquiry options. Include the cup model, outside dimensions, contact-face and side-profile photos, workpiece surface and handling conditions when you request a fit review.
Model and diameter source: euroTECH Handling online protective-cover catalogue, accessed 9 November 2026. Check fit and retention on the actual cup before selecting a cover.
Capas para ventosas destinadas ao manuseamento de vidro
As capas para ventosas da MTC proporcionam uma camada protetora adicional entre a ventosa e a peça de trabalho. São particularmente adequadas para aplicações de manuseamento de vidro, nas quais a proteção da superfície e a redução das marcas de sucção são importantes.
As ventosas a vácuo são amplamente utilizadas em toda a produção e transformação do vidro, desde o carregamento e transporte até ao corte e transformação posterior. As proteções da MTC podem ser colocadas sobre ventosas adequadas para ajudar a proteger as superfícies sensíveis do vidro durante o manuseamento.
Saiba mais sobre as ventosas a vácuo para manuseamento de vidro →
MTC Covers in Installed Applications
Explore suction cup cover installation photos and configuration notes. The latest record shows MTC.004 covers fitted to EUROTECH BLSP 200 VS-NO suction cups on a Grenzebach float glass stacking system, with system views and component details. View the MTC.004 float glass stacking configuration.
MTC Covers Referenced in Glass Manufacturers’ Processing Guidelines
Şişecam's processing guideline names Eurotech MTC 2 where contact with the coated side cannot be avoided for the specified glass products. arcon's June 2026 heat-treatable-coatings guide lists MTC in its production aids, subject to compatibility checks. These references do not establish suitability for every cover size, coating or installation.
Review the source scopes and handling requirements before assessing a candidate configuration.
Vidro revestido, laminado e isolante
Before assembly, a contact surface may still be accessible for inspection. After lamination or IGU assembly, some surfaces are enclosed. Identify the glass product, contact face and inspection stage before evaluating a cover.
Review the actual cup-and-cover configuration for fit, retention, surface results and holding performance. Use the Low-E contact review before IGU assembly for the station record and the scope of glass manufacturers’ processing instructions.
Continue to IGU line suction cups or laminated-glass cutting applications when the enquiry concerns a production-machine component.
Como evitar marcas de ventosas no vidro
A suitable suction cup cover may help reduce visible contact marks on glass. Confirm surface results and holding performance with the cover installed under the actual handling conditions.
Saiba como evitar marcas de ventosas no vidro →
Still seeing marks with suction cup covers? Check cup size and vacuum level →
Considering a different contact approach? Compare suction cup covers and non-marking suction cups
Pannkoke 388 with an MTC Cover: Published Load-Test Video
Pannkoke Vacuum Lifter published this video in July 2019 to examine the load-carrying behaviour of a Pannkoke 388 suction cup fitted with an MTC suction plate cover.
The video concerns a specific cup-and-cover combination. It does not establish a load rating for other configurations or demonstrate mark-free performance. Fit, holding capacity and surface results should be checked for your application.
For the cup-and-cover configurations and conditions behind Pannkoke's observations, see Pannkoke's written report on suction plate cover tests.
MTC Development History and Patent References
Explore the documented development history and patent references associated with euroTECH suction cup covers, including the scope and limitations of these historical records.
For equipment planning and technical purchasing, explore our perspective on surface quality in equipment design and purchasing, including a proposed brief for agreeing on contact requirements and decision responsibilities.
Assessing MTC Covers for Stone Surfaces
For quartz or another surface-sensitive stone, begin by identifying the mark and the point at which it appears. Our guide to suction cup marks on quartz slabs separates contact residue from other surface problems. A candidate MTC cover needs assessment on the actual cup and stone for fit, retention, holding performance and surface results.
Review an MTC Cover for Your Existing Suction Cup
Already have a vacuum handling system? Send the details below so EUROTECH can review a candidate MTC cover for the installed cup.
- Cup: Manufacturer, model, dimensions and shape; include photographs of the contact face and side profile.
- Workpiece: Glass product or other material, coating if present, and the surface being contacted.
- Operation: Workpiece weight, handling orientation, movement and vacuum conditions, where known.
- Requirement: The contact pattern or surface issue observed, the current cover if any, and the candidate MTC model if already selected.
Unknown details are fine for an initial enquiry. A dimensional match identifies a candidate for review; it does not establish compatibility, a working load or approval for the application.
Mais sobre ventosas: