Cubiertas para ventosas
Cubiertas para ventosas MTC
EUROTECH MTC suction cup covers fit over suitable vacuum suction cups and suction plates to provide a non-woven contact layer for glass and other surface-sensitive workpieces. They reduce direct contact between the cup material and the workpiece and may help reduce visible contact marks. Select a candidate cover by cup dimensions and profile, then review the complete configuration for the intended application.
MTC Cover Options at a Glance
- Contact layer: Non-woven cover fitted over a suitable suction cup or suction plate.
- Published round-cup size references: Options from 20 to 550 mm. Check the individual ranges in the size table; this is not a continuous fit range or a lifting-capacity rating.
- Retention: Integrated elastic band. Check fit and retention on the actual cup profile.
- Other dimensions or shapes: Send the cup dimensions and photographs for review.
View MTC models and cup-size references or use the MTC suction cup cover selector to identify a candidate size.
Need help with an existing installation? See what to include in your enquiry.
Cubiertas para ventosas MTC
MTC covers form a non-woven contact layer between a suitable suction cup and the workpiece, helping reduce direct elastomer contact and visible contact marks.
SSUZ Covers for Suction Cup Storage
SSUZ covers protect suction cups when they are not in use. For a workpiece-contact cover used during handling, review the MTC options on this page.
Las marcas que dejan las ventosas en el cristal pueden deberse a la contaminación, la fricción, las propiedades del material, la presión de contacto y otras condiciones de funcionamiento. Lee «¿Por qué las ventosas dejan marcas en el cristal?».
Consulta la guía de tallas de las fundas para ventosas de MTC
Las fundas para ventosas de MTC están disponibles en una amplia gama de tamaños para ventosas redondas y ovaladas. La elección de la funda adecuada depende principalmente de las dimensiones y la forma de la ventosa.
Utiliza nuestra guía de tallas para encontrar una cubierta MTC adecuada para tu aplicación. Si tu talla no aparece en la lista, envíanos el diámetro de la ventosa, sus dimensiones o una foto para que podamos ayudarte.
- The cover fits over a suitable suction cup or suction plate and is secured with an integrated elastic band. Confirm retention throughout the handling cycle.
- The round-cup selection references listed below range from 20 mm to 550 mm. These dimensions are fit references, not lifting-capacity ratings.
- Confirm material suitability for the workpiece, temperature and any cleaning agents used in your process.
| MTC model | Cup-size reference (mm) |
|---|---|
| MTC 39 | 20 |
| MTC 31 | 40 |
| MTC 8 | 55 - 60 |
| MTC 9 | 70 - 80 |
| MTC 63 | 85 - 95 |
| MTC 1 | 100 - 115 |
| MTC 2 | 120 - 130 |
| MTC 14 | 140 - 150 |
| MTC 3 | 160 - 190 |
| MTC 4 | 200 - 220 |
| MTC 5 | 230 - 250 |
| MTC 30 | 250 - 280 |
| MTC 6 | 280 - 320 |
| MTC 7 | 330 - 350 |
| MTC 10 | 360 - 400 |
| MTC 61 | 500 - 520 |
| MTC 57 | 500 - 550 |
Fundas para ventosas destinadas a la manipulación de vidrio
Las fundas para ventosas de MTC proporcionan una capa protectora adicional entre la ventosa y la pieza de trabajo. Son especialmente adecuadas para aplicaciones de manipulación de vidrio en las que es importante proteger la superficie y reducir las marcas de succión.
Las ventosas de vacío se utilizan ampliamente en toda la cadena de producción y procesamiento del vidrio, desde la carga y el transporte hasta el corte y el procesamiento posterior. Las fundas de MTC pueden colocarse sobre las ventosas adecuadas para ayudar a proteger las superficies delicadas del vidrio durante su manipulación.
Más información sobre las ventosas de vacío para la manipulación de vidrio →
MTC Covers in Installed Applications
Explore suction cup cover installation photos and configuration notes. The latest record shows MTC.004 covers fitted to EUROTECH BLSP 200 VS-NO suction cups on a Grenzebach float glass stacking system, with system views and component details. View the MTC.004 float glass stacking configuration.
MTC Covers Referenced in Glass Manufacturers’ Processing Guidelines
Şişecam's processing guideline names Eurotech MTC 2 where contact with the coated side cannot be avoided for the specified glass products. arcon's June 2026 heat-treatable-coatings guide lists MTC in its production aids, subject to compatibility checks. These references do not establish suitability for every cover size, coating or installation.
Review the source scopes and handling requirements before assessing a candidate configuration.
Vidrio recubierto, laminado y aislante
El vidrio recubierto, laminado y aislante suele requerir un cuidado especial durante su manipulación al vacío. Las huellas dactilares, la suciedad y las marcas dejadas por las ventosas pueden resultar especialmente problemáticas en la producción de vidrio laminado y aislante, ya que algunas superficies quedan encerradas o son inaccesibles tras el montaje y ya no se pueden limpiar fácilmente.
MTC covers can help reduce direct elastomer contact with suitable glass surfaces. Validate surface quality after the relevant handling and downstream processes, particularly where the contacted surface will become inaccessible after assembly.
Cómo evitar las marcas de las ventosas en el cristal
A suitable suction cup cover may help reduce visible contact marks on glass. Confirm surface results and holding performance with the cover installed under the actual handling conditions.
Descubre cómo evitar las marcas de las ventosas en el cristal →
Still seeing marks with suction cup covers? Check cup size and vacuum level →
Considering a different contact approach? Compare suction cup covers and non-marking suction cups
Pannkoke 388 with an MTC Cover: Published Load-Test Video
Pannkoke Vacuum Lifter published this video in July 2019 to examine the load-carrying behaviour of a Pannkoke 388 suction cup fitted with an MTC suction plate cover.
The video concerns a specific cup-and-cover combination. It does not establish a load rating for other configurations or demonstrate mark-free performance. Fit, holding capacity and surface results should be checked for your application.
MTC Development History and Patent References
Explore the documented development history and patent references associated with euroTECH suction cup covers, including the scope and limitations of these historical records.
Review an MTC Cover for Your Existing Suction Cup
Already have a vacuum handling system? Send the details below so EUROTECH can review a candidate MTC cover for the installed cup.
- Cup: Manufacturer, model, dimensions and shape; include photographs of the contact face and side profile.
- Workpiece: Glass product or other material, coating if present, and the surface being contacted.
- Operation: Workpiece weight, handling orientation, movement and vacuum conditions, where known.
- Requirement: The contact pattern or surface issue observed, the current cover if any, and the candidate MTC model if already selected.
Unknown details are fine for an initial enquiry. A dimensional match identifies a candidate for review; it does not establish compatibility, a working load or approval for the application.
Más información sobre las ventosas de vacío: