吸着パッドカバー
MTC吸着パッドカバー
EUROTECH MTC suction cup covers fit over suitable vacuum suction cups and suction plates to provide a non-woven contact layer for glass and other surface-sensitive workpieces. They reduce direct contact between the cup material and the workpiece and may help reduce visible contact marks. Select a candidate cover by cup dimensions and profile, then review the complete configuration for the intended application.
MTC Cover Options at a Glance
- Contact layer: Non-woven cover fitted over a suitable suction cup or suction plate.
- Published round-cup size references: Options from 20 to 550 mm. Check the individual ranges in the size table; this is not a continuous fit range or a lifting-capacity rating.
- Retention: Integrated elastic band. Check fit and retention on the actual cup profile.
- Other dimensions or shapes: Send the cup dimensions and photographs for review.
View MTC models and cup-size references or use the MTC suction cup cover selector to identify a candidate size.
Need help with an existing installation? See what to include in your enquiry.
吸着パッドカバー MTC
MTC covers form a non-woven contact layer between a suitable suction cup and the workpiece, helping reduce direct elastomer contact and visible contact marks.
SSUZ Covers for Suction Cup Storage
SSUZ covers protect suction cups when they are not in use. For a workpiece-contact cover used during handling, review the MTC options on this page.
ガラスに吸盤の跡がつく原因は、汚れ、摩擦、材質、接触圧力、その他の使用条件などによるものです。「なぜ真空吸盤はガラスに跡を残すのか？」をご覧ください。
MTC 吸盤カバーのサイズガイドをご覧ください
MTCの吸盤カバーは、丸型および楕円形の吸盤に対応した幅広いサイズを取り揃えております。適切なカバーの選定は、主に吸盤の寸法と形状によって決まります。
当社のサイズガイドをご参照の上、お客様の用途に適したMTCカバーをお選びください。ご希望のサイズが一覧にない場合は、吸盤の直径、寸法、または写真をお送りいただければ、ご対応いたします。
- The cover fits over a suitable suction cup or suction plate and is secured with an integrated elastic band. Confirm retention throughout the handling cycle.
- The round-cup selection references listed below range from 20 mm to 550 mm. These dimensions are fit references, not lifting-capacity ratings.
- Confirm material suitability for the workpiece, temperature and any cleaning agents used in your process.
| MTC model | Cup-size reference (mm) |
|---|---|
| MTC 39 | 20 |
| MTC 31 | 40 |
| MTC 8 | 55～60 |
| MTC 9 | 70～80 |
| MTC 63 | 85～95 |
| MTC 1 | 100 – 115 |
| MTC 2 | 120 – 130 |
| MTC 14 | 140 – 150 |
| MTC 3 | 160 – 190 |
| MTC 4 | 200 – 220 |
| MTC 5 | 230 – 250 |
| MTC 30 | 250 – 280 |
| MTC 6 | 280 – 320 |
| MTC 7 | 330 – 350 |
| MTC 10 | 360 – 400 |
| MTC 61 | 500 – 520 |
| MTC 57 | 500 – 550 |
ガラス取り扱い用吸盤カバー
MTCの吸盤カバーは、吸盤と被加工物の間に追加の保護層を形成します。これらは、表面の保護や吸着跡の低減が重要なガラス取り扱い用途に特に適しています。
真空吸盤は、ガラスの生産および加工の全工程において、積み込みや搬送から切断、さらにはその後の加工に至るまで、広く使用されています。MTCカバーを適切な吸盤に取り付けることで、取り扱いの際にデリケートなガラス表面を保護することができます。
MTC Covers in Installed Applications
Explore suction cup cover installation photos and configuration notes for examples of installed arrangements and the details to review for your application.
MTC Covers Referenced in Glass Manufacturers’ Processing Guidelines
Şişecam's processing guideline names Eurotech MTC 2 where contact with the coated side cannot be avoided for the specified glass products. arcon's June 2026 heat-treatable-coatings guide lists MTC in its production aids, subject to compatibility checks. These references do not establish suitability for every cover size, coating or installation.
Review the source scopes and handling requirements before assessing a candidate configuration.
コーティングガラス、合わせガラス、および複層ガラス
コーティングガラス、合わせガラス、複層ガラスは、真空ハンドリングの際に特別な注意を要することがよくあります。指紋、汚れ、吸盤の接触跡などは、合わせガラスや複層ガラスの製造において特に問題となり得ます。これは、組み立て後に一部の表面が密閉されたり、手が届かなくなったりして、容易に清掃できなくなるためです。
MTC covers can help reduce direct elastomer contact with suitable glass surfaces. Validate surface quality after the relevant handling and downstream processes, particularly where the contacted surface will become inaccessible after assembly.
ガラスに吸盤の跡がつかないようにする方法
A suitable suction cup cover may help reduce visible contact marks on glass. Confirm surface results and holding performance with the cover installed under the actual handling conditions.
Still seeing marks with suction cup covers? Check cup size and vacuum level →
Considering a different contact approach? Compare suction cup covers and non-marking suction cups
Pannkoke 388 with an MTC Cover: Published Load-Test Video
Pannkoke Vacuum Lifter published this video in July 2019 to examine the load-carrying behaviour of a Pannkoke 388 suction cup fitted with an MTC suction plate cover.
The video concerns a specific cup-and-cover combination. It does not establish a load rating for other configurations or demonstrate mark-free performance. Fit, holding capacity and surface results should be checked for your application.
MTC Development History and Patent References
Explore the documented development history and patent references associated with euroTECH suction cup covers, including the scope and limitations of these historical records.
Review an MTC Cover for Your Existing Suction Cup
Already have a vacuum handling system? Send the details below so EUROTECH can review a candidate MTC cover for the installed cup.
- Cup: Manufacturer, model, dimensions and shape; include photographs of the contact face and side profile.
- Workpiece: Glass product or other material, coating if present, and the surface being contacted.
- Operation: Workpiece weight, handling orientation, movement and vacuum conditions, where known.
- Requirement: The contact pattern or surface issue observed, the current cover if any, and the candidate MTC model if already selected.
Unknown details are fine for an initial enquiry. A dimensional match identifies a candidate for review; it does not establish compatibility, a working load or approval for the application.