New Zealand H1 Glazing Requirements for IGU

New Zealand H1 Glazing Requirements: What They Mean for IGU Manufacturing For an IGU manufacturer, “H1-compliant glazing” is the start of a specification discussion. It does not yet identify the panes that a production line will handle. The factory still needs the glass build-up, coating, dimensions and processing requirements. The equipment supplier needs to know which of those panes—or which […]

Triple-Glazed IGU Production

Triple-Glazed IGU Production: Handling Conventional and Thin-Center-Pane Units A request to “handle triple glazing” leaves an important question unanswered: what is being lifted at that moment? It could be a conventional outer pane, a thin center pane entering the assembly line, or a completed insulating glass unit. The dimensions may be similar, but the contact surface, stiffness, mass and support […]

Why a Stone Slab Loader Loses Vacuum

Why a Stone Slab Loader Loses Vacuum: Cup, Surface and System Checks A stone slab loader that loses vacuum does not always need a different suction cup. A worn sealing edge is one possibility. An uncovered cup, a leaking connection or a different slab contact surface can produce a similar complaint. The most useful first step is to describe the […]

Suction Cup Marks on Quartz Slabs

Suction Cup Marks on Quartz Slabs: What Fabricators Should Check Before the Next Lift A ring appears on a quartz slab after handling. It follows the outline of a cup, but wiping the surface does not immediately explain what happened. Before changing the rubber or reaching for a stronger cleaner, establish when the mark appeared and what type of change […]

Replacing Suction Cups on Stone Slab Loaders

Replacing Suction Cups on Stone Slab Loaders: What to Measure Before Ordering The loader is ready, the next slab is at the rack, and one cup will not seal as it used to. The first purchasing question is often simple: “Can you supply another cup with this diameter?” A useful replacement enquiry needs a little more information than that. Replacement […]

진공 게이지가 정상으로 표시되는데도 유리가 미끄러지는 이유는 무엇일까요?

진공 게이지가 정상 수치를 표시한다고 해서 흡착컵이 미끄러짐에 대한 충분한 저항력을 갖추고 있다는 것을 의미하지는 않습니다. 게이지에는 측정 지점의 압력만 표시될 뿐입니다. 유효 흡착 면적이 너무 작거나, 접촉면의 접착력이 떨어졌거나, 가속도 및 가공력이 허용 가능한 고정 용량을 초과하는 경우 유리는 여전히 움직일 수 있습니다. EUROTECH의 유리 취급 경험에 따르면, 흡착컵의 크기 선정과 상태 […]

고온 플라스틱 부품용 진공 흡착컵

고온 플라스틱 부품용 진공 흡착컵: 소재 선정 가이드 고온 플라스틱 부품용 진공 흡착컵을 선정할 때는 단순히 소재의 최대 온도만 확인하는 것 이상의 고려가 필요합니다. 흡착컵은 밀봉 상태를 유지해야 하며, 이동 중에 공작물을 지지하고 안정적으로 분리할 수 있어야 합니다. 동시에, 플라스틱 부품은 여전히 따뜻하거나 상대적으로 유연할 수 있으며, 접촉 자국에 민감할 수도 있습니다. […]

NBR, HNBR, FKM 진공 흡착컵 비교

NBR, HNBR, FKM 진공 흡착컵 비교: 선택 방법 NBR, HNBR, FKM 진공 흡착컵 중 하나를 선택하려면 먼저 흡착컵이 실제로 어떤 조건에 노출되는지 파악해야 합니다. 즉, 공작물 표면, 접촉 온도, 오일이나 화학 물질, 취급 동작, 생산 주기 등을 고려해야 합니다. NBR은 일반 산업용 취급에 흔히 사용되는 소재입니다. 내열성이 향상된 제품이 필요한 경우 HNBR을 고려해 볼 수 있습니다 […]

품질 개선에서 탄소 감축으로

흡착컵 자국을 줄이는 것은 주로 품질 개선에 해당하지만, 그 영향은 제품의 외관을 훨씬 넘어설 수 있습니다. 유리 제조 과정에서 추가되는 모든 세척 작업, 재가공 공정 또는 불량품은 본래라면 피할 수 있었던 자원을 소모하게 됩니다. 즉, 취급 품질을 개선하면 생산 공정 전반에 걸쳐 자원 효율을 높이고 에너지 소비를 줄이는 데에도 기여할 수 있습니다. euroTECH의 MTC 흡착 […]

유리 취급 시 흡착컵은 어떻게 작동하나요?

유리 취급 시 흡착컵의 작동 원리 이해 진공 흡착컵은 제조, 건설, 자동차 산업에 이르기까지 다양한 분야에서 유리 취급 방식에 혁명을 일으켰습니다. 이 흡착컵은 손상이나 부상의 위험 없이 섬세한 자재를 안전하고 효율적으로 들어 올리고 이동할 수 있는 방법을 제공합니다. 경우에 따라 진공 흡착컵을 자동화하여 […]을 만들 수도 있습니다.